A2 Hosting still has not fixed the Database after their servers failed AGAIN. A2 Hosting is the WORST!
Because of this, new posts are currently missing and I can only HOPE they eventually recover the table they didn't restore after their latest failure.












Next Post - Previous Post       List View



8/4/2014 3:53:35 PM

Fending Off Rodent Invasion:  Dryer Vent Cover



After a wild chipmunk climbed into the dryer vent and took a leap down the pipe, I decided it was past time to replace the vent cover.  Of course, I had one on hand because I noticed the flap inside didn't close properly back when we were doing some repair work on the roof trim that the roofers screwed up, but I just had not gotten around to getting the replacement done.  It is something like number 39 on my list of things todo, so it isn't all that surprising that I didn't think it was an emergency.

Really... it has been that way probably since before we moved in, but I guess once you notice an issue, you should fix it right away, or you may end up with Mr. Chippy wandering your house.  Additionally having a vent flap that opens and closes properly can reduce lint build-up and risk of fire, and reduce moisture from coming into your dryer from the vent.

So, in case you, too, need to replace your dryer vent cover and fend of invading rodents, here is a break-down on the steps I took.

First, it is important to note that new houses probably have easier to remove vent covers than older houses.  In my case, our house is medium in age and had a nice metal weather-cover, but a piece of crap-stuck-open-just-partly metal vent flap.  I could have torn out the wood frame, removed all the metal, and started from scratch, but it would also probably have torn a lot of the surrounding siding and really there was nothing wrong with the wood frame, so I started by cutting the metal cover with tin-snips up the sides so that I could see how hard the flap would be to remove.

The worst problem with the existing flap was that it was not only bent out of shape, but could not open and close fully because of the sides of the cover being too small.  However, it pulled right out since it was only attached by a couple loose-fit tabs.

 

After inspecting the hole compared to the wood frame, I decided to remove the rest of the metal weather-cover altogether, and use paintable caulking to fill the gap later.  

 

However, a little more metal needed to be cut and curled away from the vent pipe opening before the new cover could be pushed into it.

 

A tight fit is a good thing, but the fit was so tight that the new cover's pipe just would not go inside the other pipe enough to come flush with the wood frame.

 

To fix this I carefully clipped several slits partway up the cover's pipe so that it would slip inside the vent pipe enough to meet the wood trim.

 
 

With a tight but flush fit, I was ready to see if some long screws would contact enough to hold the cover.

 

Luckily, the screws made solid contact, so I did not need to add more wood trim or additional anchoring.  I backed the screws out a little to add caulking under the vent cover sides, then tightened them back down.

 
 

It took several bands of caulking to fill the area above and below the vent cover, but a weather-tight seal is worth it.

 

Then I smoothed the caulk on all the edges and covered a few areas where the wood trim needed it, too.  The additional caulk on the wood trim doesn't look spectacular right now, but it protects the wood and can be painted later.

 

The rodent-guard clips onto the vent cover so that it can be cleaned if lint builds up on it, but the clips didn't fit very firmly with the back clips barely holding on.

 

So with a lighter and some very careful bending, I pushed the clips tighter and curved the back edge more to make the sides much more snug.

 
 

The fit is now snug and hopefully between the guard and the properly closing flap, rodents should no longer get in the house... at least from the dryer vent.

 


     POST LINKS BACK TO:
          8/4/2014 3:47:22 PM - Saturday... A Study in Disaster Mitigation


Next Post - Previous Post       List View
COMMENTS

8/4/2014 5:16:20 PM Punkin
You are brilliant as always and a great idea and one I will definitely keep for future use as I have a vent close to the ground and so far we have been lucky.

8/5/2014 9:30:33 AM TinkerT
Might be a good idea to check your vent sometime and see if it's flap closes properly.  I think having that part open was most of what enticed the little rodent to come in, though I can't imagine why he thought jumping down the slick pipe six foot to my dryer was a good idea.

8/5/2014 4:05:03 PM Hubby
He probably thought he was an adventurer going down a dark tunnel when suddenly the floor fell out from underneath him and he slid down the slick greased metal of the tube, hitting the bottom with a thud. Then of course during his daring attempt at escaping, what was obvious to his little rodent brain, the deadly trap things attempted to beat him senseless and cook him... all in all, if he did make it outside, either it will be the boogie man story he tells everyone, or it will be the mythical slaying of the Titans and all the other little Chippys will want to emulate him. Joy...

8/5/2014 4:51:56 PM TinkerT
Nice.  We will be the story that every Chippy tells his children.  But is it a cautionary tale, or a how-to?

Add Your Comment...


Please Keep All Comments Family-Friendly

Name / Nickname:  
Comment:  
Email:   (Optional)
      Notify me of new Comments/Replies to this post by email
      Remember my Email for future comments
Your Email is Never Shared. Email is only required if you want to be notified
of new comments or if you are entering a give-away.


Please Type This Verification Code:   v8imbv    (Code is case sensitive.)


TinkerT Terms & Disclaimer


     Step one to DIY is safety. Use applicable safety equipment, read instructions, and handle all tools with care. While this site encourages a Do-It-Yourself attitude and has ideas and how-to posts, it is not responsible for any problems that arrise from attempting similar DIY projects.
     Familyweb.us and TinkerT makes no representations or warranties of any kind (expressed or implied) about the completeness, accuracy, reliability, suitability, or gramatical correctness of any information or recomendations contained on this site or found by following any link on this site. All the information provided on TinkerT is for general information and entertainment purposes only. Following any advice or information on this site is done "At Your Own Risk". Under no circumstances will Familyweb.us or TinkerT be liable for any loss or damage (including without limitation direct, indirect, or consequential loss or damage) arising from use or misuse of information provided in this website.
     Copyright Policy - Unless otherwise noted, Familyweb.us is the legal copyright holder of all material on this website. Submitions and comments will be considered the property of Familyweb.us and may be used, whole or in part, for purposes on the site or other related projects. Please feel free to copy and reprint any portion of the articles and posts on this site. However, you must include a clear label for where you got the material and include a link to the appropriate page for the post that material was copied from.
     The opinions expressed by any Third Parties (including commenters) are their own and do not represent the position or believe of Familyweb.us or TinkerT. TinkerT reserves the right to remove or edit comments for any reason deemed nessesary, including, but not limited to: spam, offensive language, inapropriatness, and general rudeness.
     TinkerT will never sell or share your email with any third party and will not send you advertizements or spam.
     Familyweb.us and TinkerT reserve the right to change the focus of, close, or sell this blog site without warning.

     While TinkerT and Familyweb.us strive to ensure all posts and comments are PG13 or less, it makes no guarantees of this and requests that anyone under 17 ask their parent's permission before signing up for the newsletter or reading this site.

     These terms and conditions are subject to change at anytime without notice.












aquariums
archives
cooking
crafts
denver
DIY
electronics
home improvement
ideas
landscaping
low budget
mountain living
nature
outdoor
painting
plants
style
the tilt
tools
travel
woodworking

instant pot
  smart scripts